vasupservers.blogg.se

Okidata microline 320 turbo power switch
Okidata microline 320 turbo power switch









okidata microline 320 turbo power switch
  1. #OKIDATA MICROLINE 320 TURBO POWER SWITCH DRIVER#
  2. #OKIDATA MICROLINE 320 TURBO POWER SWITCH PC#
  3. #OKIDATA MICROLINE 320 TURBO POWER SWITCH FREE#

The print wires fixed to each armature are thus concealed under the wire guide. (a) When the printhead is idle, the armature is attracted by a permanent magnet and the spring fixing the armature is compressed. (2) Operation of printhead (See Figure 2-3.) to control and maintain the impact necessary for each printing pin at the fixed value. The head drive time is lengthened to compensate for the amount of voltage drop by monitoring the POWLEV signal once every 500 μ sec. + 40V is converted into the POWLEV signal (0V to +5V) by R28 and R29 and input into the A/D port of the MPU to control the drive time and the print speed (pass number) of the head. (2) Alarm processing when DC power is low. This cause the secondary coil (40V) of the transformer to be short-circuited, causing an overcurrent to flow through the primary coil and making the AC fuse (transformer assy) open. If the drive time of any drive circuit exceeds the specified time, the drive fault alarm circuit sends an ALARM-N signal to turn on the SCR (SO). This circuit monitors the drive time using the HDALM signal interlocked with the overdrive signal of each drive circuit. The program here sets the mode of the LSI including the MPU, checks the memories (ROMs and RAMs), then carries out carriage homing, and determines the LF motor phase.įinally, the program establishes the interface signals (P-I/F: ACK-P signal sending, and S-I/F: BUSY-N signal off) and lights the SELECT lamp to inform the ready state for receiving to the host side and ends the initialize operation. Reset operation by I-PRIME starts program to initialize, but does not reset the MPU. When resetting ends, the program starts and the LSIs are reset by MPU via LSIRST-N. This printer is initialized when the power is turned on or when the I-PRIME-N signal is input from the host side via the parallel interface.įor the initialize operation, the RST-N signal is first output from the reset circuit to reset the MPUs and LSIs.

#OKIDATA MICROLINE 320 TURBO POWER SWITCH DRIVER#

The function of this microprocessor is to provide a central mechanism for the entire printer by executing the control program through the LSI and driver circuits. 8-bit parallel port × 3 (bitwise I/O specification available).The following characteristics are also provided: It is capable of accessing up to 1M word program memory and 1M bytes of data memory. The processor has a 20 bit address bus and a 16 bit data bus.

okidata microline 320 turbo power switch

This processor is a CMOS single-chip computer with integrated peripheral device functions and a 16 bit MPU core, all OKI original architecture. The power to other electrical parts is also distributed through the connectors within the control board.Ģ.1.2 Microprocessor and the Peripheral Circuit The power to the control board is supplied by the power board through the connector cord. The control board is made up of the microprocessors, peripheral circuits, drive circuits, sensors and interface connectors. 2-1 shows the block diagram of the printer.

#OKIDATA MICROLINE 320 TURBO POWER SWITCH FREE#

Free shipping offers only apply to the continental US.The electrical operation of the printer circuit is described in this section.įig.

  • Fixed or free shipping offer does not apply to items shipped on pallets, please call for rates on those items.
  • All products are shipped and delivered on business days.
  • If you have a rush order, or need an item delivered on Saturday please call to request faster shipping.
  • Products usually ship within two business days after payment.
  • The purchaser is responsible for all shipping costs and insurance.
  • Item(s) should be securely packed for safe return.
  • Item(s) must be received in original condition preferably in the same packing materials.
  • Item(s) must be returned within 30 days from invoice date.
  • If you need assistance finding a different product our awesome staff is ready to help. Whether you want something different or just a credit, we have you covered! This policy goes hand in hand with our company culture of delivering outstanding customer satisfaction. Rest assured, if you order the wrong items, don't like the model, or just don't need it anymore we accept returns with NO restocking fees.

    #OKIDATA MICROLINE 320 TURBO POWER SWITCH PC#

    No Hassle Return Policy & PC Certified Guarantee











    Okidata microline 320 turbo power switch